Tube-Tech MP 1A Microphone Preamplifier

价格： $3025.00 (约合人民币 ￥22083) （注：此价格为美国市场参考价格，非本站出售价格，本站正在积极搭建代购渠道！）

• 浏览：183次
• 品牌：Tube-Tech
• 状况：全新
• 类别：现场音响 - 信号处理 - Mic Pre-Amps
• 一句话简介：An all-tube preamp with an amazing ability to make any mic you put through it sound great.
• 简介：The Tube-Tech MP 1A dual channel preamp and instrument DI has been one of the secrets that engineers and producers have kept to themselves for bringing the rounder and more pleasing sound of analog gear to digital recording. And where some preamps tend to work well with certain mics but not others, the MP 1A also has the uncanny ability to make any mic your put through it sound great. A truly phenomenal-sounding preamp, the MP 1A excels on electric guitars and vocals. To give you an idea of its versatility, the MP 1A has been part of Julio Iglesias' vocal chain for years and is the preamp that Frank Fillipetti used to record Johnathan Davis' vocals on Korn's Take a Look in the Mirror.
  
  Tube-Tech MP 1A, First Take:
  • Dual channel all-tube mic preamp and instrument DI
  • Designed for ultra low-noise operation
  • Switchable 20dB pad, can be used as a unity gain line amplifier, +70dB mic input gain
  • DI input with switchable high-pass filter and +60 gain
  
  
  Dual Channel All-Tube Mic Preamp And Instrument DI
  The rackmount Tube-Tech MP 1A microphone preamplifier is a combined two channel microphone and DI preamplifier. Each amplifier consists of a microphone input transformer with a step-up of +10 dB, a dual tube preamplifier with a stepped gain (5dB/step, passive and active), an output amplifier with two dual tubes in push-pull and an output transformer. The high impedance DI inputs are unbalanced and placed in the circuit directly after the input transformer, with a gain ranging from +10dB to +60dB.
  
  Designed For Ultra Low-Noise Operation
  The amplifiers are all tube based and the heaters are fed stabilized DC-voltage only. This prevents any variation in the DC energy when combined with the musical signal, which would otherwise cause certain types of distortion or hum. All transformers, with the exception of the mains transformer, are enclosed in MU-metal cans. MU-metal (pronounced mew-metal) is a highly permeable alloy that absorbs and redirects interfering magnetic fields away from the transformers. Input and output transformers come with a static screen between the primary and secondary wirings. These screens shield the secondary from the primary and prevent RF (radio frequency) electromagnetic noise from getting across.
  
  Switchable Pad, +70dB GainThe microphone inputs are provided with a switchable -20dB attenuation pad in front of the mic transformer and switchable +48V phantom-power. The microphone input is capable of accepting levels of up to +6 dBU (1.55V) at 40 Hz without the pad and +26dBU (15.5V) at 40 Hz with the pad, so the microphone input can be used as a unity gain line amplifier*. The gain switch for the mic inputs has a range from +20dB to +70dB in steps of 5dB, which allows use with ribbon mics. A high pass filter for the microphone and the DI input is switchable between off, 20 Hz (12dB/octave) and 40 Hz (6dB/octave). It is advisable to use this filter in environments with high levels of very low-frequency disturbances. Gain errors between the two channels are less than 0.5dB at any gain setting. The two amplifier circuits are completely separated and the cross talk between channels is below -60dB ranging from 20Hz to 20kHz.
  
  * Most audio products use op-amps running from
• 技术参数：
  1. Tube based push-pull output amplifier
  2. Gain from +20 dB to +70 dB in 5 dB increments
  3. Pad in front of input transformer (-20 dB)
  4. Built-in +48 V phantom power
  5. Microphone input impedance = 1,2 kohm
  6. CMRR >60 dB @ 10kHz
  7. Direct Instrument Jack-socket input for various instruments
  8. DI input impedance > 1 Mohm
  9. Frequency Response @ -3 dB: 15 Hz to 60 kHz
  10. Typical noise figure: 5 dB @ 200 ohm